How To Cut Vinyl Siding For Ledger Board

I think they sell 'em at the big box. Here's the basic steps involved for installing flashing on vinyl along with a few good tips to consider and.

Trim Board Manufacturers Engineered Wood Trim Boards

You can't anchor exterior features directly to the vinyl siding panels.

How to cut vinyl siding for ledger board. Normally you'd remove the siding, attach the ledger and use a z flashing to keep water from running down behind it. Since you will be removing the vinyl anyway so you can get the ledgers properly flashed and detailed, you can just cut it with a pair of snips. A tool like this helps a lot in removal and replacement of vinyl siding in the middle of a wall:

I would just put 2x4 blocks between the ledger and concrete and leave the siding. Set the blade depth so you won't cut into the house sheathing below the siding. When the back flashing needs to be cut around an obstacle, measure for the notch and cut with tin snips, or slice several passes with a knife.

First, ensure your circular saw is equal to the thickness of the deck, then cut the ledger outline. Secure the utility trim, also called under sill trim, just below the soffit, using the same technique to secure the utility trim as you used with the vinyl siding. Slip flashing under the siding.

Step 1 mark the location of the ledger against the siding. Click to see full answer. Cut two 24 by 2 by 10 inch pieces of wood and scab them onto the floor joist on each side of the removed ledger.

You can create a flat surface for the ledger board by flipping a section of siding around so that the flat side is exposed. Expose the ledger board of your building by removing any siding covering the bottom of the wall where the wood meets the foundation. A dribble of water on the blade helps with the dust.

Where the back flashing needs to be cut around an obstacle, measure for the notch and cut with tin snips, or slice several passes with a knife. Install the ledger overtop of the siding or remove the siding, attach the ledger and recase around it? Loosen the siding left above the ledger so that you can slip flashing under the paper under the siding.

Start by making an outline on the siding where you want to position the ledger board. Cut into the wall, attach the ledger board to the rim joists and nail it to the studs. Aluminum and vinyl siding can easily be removed with tin snips from an area one foot surrounding the ledger board location.

Never attach a ledger board directly over siding of any kind. But the panels themselves aren't very thick. It's the same process for a deck.

You can then trim the pieces to be reinstalled with a j channel after the deck is completed for a clean, finished look. The vinyl siding interlocks with itself to form a cohesive, protective shell around the house; Aluminum and vinyl siding can easily be removed with tin snips from an area one foot surrounding the ledger board location.

Instead, cut a hole through the siding and affix a mounting block. Snap a chalk line, cut out the siding and tack up the ledger board. Wood or concrete siding will have to.

Slide the flashing underneath the siding 1. When slipping the flashing under the siding, be sure to slide the flashing to. Slide the flashing underneath the siding 1 inch.

Then slip flashing behind the siding, covering the top edge of the ledger. When slipping the flashing under the siding, be sure to slide the flashing to the left or right of the ledger by at least 2. Run flashing behind the siding and over the ledger as should have been done in the first place.

You can cut the siding with a diamond blade, they make one for siding but i just grabbed the blade from the tile cutter and a circular saw. Since a lot of ordinary homeowners can barely tell a hammer from a phillips screwdriver, many of them turn to the internet to find help in completing their project. What is the preferred method when attaching to a house with vinyl siding.

Decks and vinyl siding for the dummy diy. Cut away the rotted ledger board using a reciprocating saw. You cut the siding to the height you need (measure twice) and then the punch creates small tabs that stick out from the siding (only 3.

Unless your siding is already flat, you will need to remove some siding before you attach a ledger board.

How To Set Up Board and Batten or exterior siding House